28-2TITAN0019 USER MANUAL ON LINE UPS 1-10KVA Uninterruptible Power Supply
75. Connection and Operation 5.1 Connection and operation for 1K(S)/ 2K(S)/ 3K(S) 1) Inspection: Inspect the packaging carton and its content
85. Connection and Operation Figure 2: Connection diagram of 2KS(CE) and 3K(S) 2.3) Computer Connection: Connect your computer to the out
95. Connection and Operation 6) Turn Off the UPS: 6.1) In Inverter Mode: Press “ “ button continuously for more than 1 second to turn off the UPS.
105. Connection and Operation (6) the "+" terminal of the battery. The black wire is connected to the "-" terminal of the batt
116. Trouble Shooting If the UPS system does not operate correctly, please attempt to solve the problem using the table below. Problem Possible cau
127. Maintenance 7.1 Operation The UPS system contains no user-serviceable parts. If the battery service life (3 - 5 years at 25°C ambient temperatu
138. Technical Data 8.1 Electrical specifications INPUT Model No. 1K(S) 2K 2KS 3K(S) Phase Single Frequency (46~54)Hz Current(A) 7A 9A 12A
148. Technical Data 8.4 Dimensions and weights Model No. Dimensions W x D x H (mm) Net Weight kg 1K 145X400X220 14 1KS 145X400X220 7 2K 192X4
159. Introduction – 6K(S)/10K(S) 9.1 Product Specification and Performance 1) General Specification Model 6K 6KS 10K 10KS Power Rating 6KVA/4.
1610. Installation 10.1 Unpacking and Inspection 1) Unpack the packaging and check the package contents. The shipping package contains: lA UPS lA us
Contents 1. Safety and EMC Instructions...1-3
1710. Installation Note: Do not use the wall receptacle as the input power source for the UPS, as its rated current is less than the UPS’s maximum i
1810. Installation Important notes: If the UPS is used in single mode, JPI and JP2 must be connected by 10AWG(6mm2). If the UPS is used in parallel
1910. Installation 10.4 Parallel operation 1. Brief introduction of the redundancy N+X is currently the most reliable power supply structure. N rep
2011. Operation and Operating Mode Operation and maintenance 1) To perform the general operation, follow the stand-alone operating requirement。 2) St
2111. Operation and Operating Mode 2) For long back up time model (“S” model), please make sure that the battery breaker is in “ON” position. 3) Dur
2211. Operation and Operating Mode 2) New UPS input & output switch should be turned off, according to port sign, link Input & output line
2311. Operation and Operating Mode Operational process of removing single UPS: 1) If want to remove UPS which is running normally, please press th
2411. Operation and Operating Mode 6. Backup time for the standard model The backup time of the long backup time model is dependent on the external
2512. Battery Maintenance l This series UPS only requires minimal maintenance. The battery used for standard models are value regulated sealed lead-a
2613. Notes for Battery Disposal and Battery Replacement 1) Before disposing of batteries, remove conductive jewelry such as necklace, wrist watches
14. Trouble Shooting...27 15
2714. Trouble Shooting Problem Possible cause Solution The #1 Fault LED and the #6 LED are turned on, the buzzer beeps continuously. The UPS transfe
2815. Operating mode for all models 1. Utility power mode The display panel in utility power mode is shown in the following diagram. The utility pow
2915. Operating mode for all models 2) When the battery capacity decreases, the number of the battery capacity LEDs turned on will be reduced
3016. Communication Port 16.1 RS232 Interface The following is the pin assignment and description of DB-9 connector. Pin # Description I/O 2 TXD
3117. Software for all models Free Software Download – WinPower WinPower is a brand new UPS monitoring software, which provides user-friendly interf
3218. Appendix 1-Display Panel (for 6K(S)/10K(S)) l Power ON/OFF: To turn on the UPS simply by pressing the “ON” button on the front panel conti
33Appendix 2-The Corresponding Form of the LED Display for 6K(S)/10K(S) LED display No. Operating state 1# 2# 3# 4# 5# 6# 7# 8# 9# 10# Alarm warnin
34Appendix 3-Back Panel Back View of 1K & 1KS Figure 1: Back View of 1K & 1KS Back View of 2K(S) Non CE-certified
35 Back View of 3K(S) Non CE-certified Back View of 3K(S) CE-certified Back view of 6K
36 Back view of 10K Back view of 10KS
11. Safety and EMC instructions Please read carefully the following user manual and the safety instructions before installing the unit or using the
37 614-06440-10
21. Safety and EMC instructions 1.2 Operation ★ Do not disconnect the mains cable on the UPS or the building wiring socket (grounded shockproof socke
31. Safety and EMC instructions 1.4 Transport ★ Please transport the UPS only in the original packaging (to protect against shock and impact). 1.5 S
42. Description of commonly used symbols Some or all of the following symbols may be used in this manual. It is advisable to familiarize yourself wit
53. Introduction – 1K/2K/3K This On-Line-Series is an uninterruptible power supply incorporating double-converter technology. It provides perfect pr
64. System Description Figure 1: Display Panel Switch Function ON - Switch Turn on UPS system: By pressing the ON-Switch “I” the UPS syst
Comments to this Manuals