Uninterruptible Power Supplies Online UPS 2K User Manual

USER MANUAL On-Line UPS 1000VA/1500VA/2000VA/3000VA Uninterruptible Power Supply System 614-

10 Note: Three or more EBMs can be connected to the UPS in the same way as shown above. Note: After connect the EBMs, please do

11 Use No. 12 AWG (for 3KS input wire), 90°C copper wire and 4.4 lb-in Torque force when connecting to terminal block. Use No. 10AWG (

12 1.3.1 UPS and Battery Care For the best preventive maintenance, keep the area around the UPS clean and dust-free. If the atmosphere is very

13 1.3.4 Replacing UPS Internal Batteries Follow the steps and Charts as below to replace batteries: 1. Take off the LCD box, and remove the scr

14 1.3.5 Testing New Batteries For a battery test, please check:  The batteries must be fully charged.  The UPS must be in Normal mode with no acti

15 1.6 Standards * Safety IEC/EN 62040-1 * EMI Conducted Emission...:IEC/EN 62040-2 Category C1 Radiated Emis

16 2. Description of Commonly Used Symbols Some or all of the following symbols may be used in this manual. It is advisable to familiarize yourself w

17 3. Introduction This On-Line-Series is an uninterruptible power supply incorporating double-converter technology. It provides perfect

18 4. Panel Description The Display Panel Switch Function ON-Button Turn on UPS system: By pressing the ON-Button “I” the

19 The LCD Display Display Function Display Function Input Information Output Information It indicates input voltage/frequency value, w

CONTENT 1. Safety and EMC Instructions ... 4 1.1 Installation ...

20 5. Connection and Operation 5.1 Inspection Inspect the packaging carton and its contents for damage. Please inform the transport agency imm

21 (2) UPS Output Connection The output of the UPS is IEC socket-types. Simply plug the load power cord to the output sockets to complete conne

22  NC Normally the EPO connector is closed with a wire on the rear panel. Once the connector is open, the UPS would stop the output until the EPO

23 change within 30 seconds; in resting mode, UPS will detect the change within 3 minutes; (2) Manual test Test the function of the UPS system by pre

24 (3) The battery connection procedure is very important. Any incompliance may result in the risk of electric shock. Therefore, the followin

25 6. Operating Mode for All Models The different string could be displayed on the LCD screen corresponding to their own operating modes, and they ar

26 Note: Please follow the following steps to connect the generator ● Activate the generator and wait until the operation is stable before supplying

27 The UPS does not have the backup function when it is in bypass mode. The power used by the load is supplied from the utility power via internal fi

28 6.7 Converter mode In converter mode, on LCD display, the mode string is “CVCF”. The UPS would free run with fixed output frequency (50Hz

29 7. Setting by LCD Module The output voltage, frequency, Bypass status and operating mode in No output mode or Bypass mode, Two Loa

9.2 Storage ... 33 9.3 Battery Replace ...

30 “Bypass Enable” is selected, and turn to no output mode in several seconds after “Bypass Disable” is selected; Operating mode could be se

31 8. Trouble Shooting If the UPS system does not operate correctly, check the operating status on the LCD display. Warning String Fault String Si

32 Battery low Battery voltage is low When audible alarm sounding every second, battery is almost empty. Charge fail The charge is broken Notify

33 9. Maintenance 9.1 Operation The UPS system contains no user-serviceable parts. If the battery service life (3~5 years at 25°C ambient temperature

34 10. Technical Data 10.1 Electrical specifications INPUT Model No. 1K(S) 1.5K(S) 2K(S) 3K(S) Phase 1 Frequency (45~55)/(54~66) Hz Max Current

35 10.4 Dimensions and weights Model 1000 1000S 1500 1500S 2000 2000S 3000 3000S UPS Case Net weight (kg) 16.2 8.4 19.7 9.3 19.7 9.3 28.6 13.2 Dimen

36 11. Communication Port 11.1 RS-232 and USB communication ports To establish communication between the UPS and a computer, connect a comp

37 11.3 USB port The UPS can communicate with a USB-compliant computer by using HID-compatible power management software. To establish

38 The following figures show schematic of the dry out/in contacts. Dry out contact schematic Dry in contact schematic The following table shows

39 12. Software Free Software Download – WinPower WinPower is a brand new UPS monitoring software, which provides user-friendly interface to

41. Safety and EMC Instructions 1.1 Installation See installation instructions before connecting to the supply. Condensation may occur if the

40 Appendix: Rear panel The UPS rear panel description table and pictures are shown as below: 1000VA /1500VA/2000VA Standard & 1000VA /1

41 3000VA Standard model rear panel 3000VA Supper charger model rear panel The EBM rear panel description table and picture are

51.1.2 Unpacking the Cabinet To unpack the system: 1. Open the outer carton and remove the accessories packaged with the cabinet. 2. Caref

6 Rack-mount setup The series can be installed in 19 inches racks. Both the UPS and external battery enclosure need 2U of rack space. Use the f

7on side of the front panel to allow the outlet wire of the EBM to pass through the gate and then reassemble front panel.

8 Connecting the EBM in a rack form 1. Using the same method as assembling UPS in a rack form, assemble EBM into the rack-mounting on the top or

9Connecting multiple EBMs in Tower form 1. Connect Earth line between UPS and the first EBM, and then connect Earth Line between the first EBM and th